HP ML350 - ProLiant - G2 Скачать руководство пользователя страница 46

Страница: 46 / 78

Removal and replacement procedures 46

Close the heatsink locking levers

Connect the heatsink fan cable to the system board ("

System board components

" on page

10.

Install the access panel ("

Access panel

" on page

11.

Do one of the following:

•

Close or install the tower bezel, as needed.

•

Slide the server back into the rack.

12.

Power up the server.

PPM

NOTE:

PPM 1 is embedded into the system board.

To remove the component:

Power down the server (on page

Do one of the following:

•

Unlock and remove the bezel ("

Front bezel

" on page

•

Extend the server from the rack (on page

Remove the access panel ("

Access panel

" on page

Open the PPM latches.

Содержание ML350 - ProLiant - G2















































































Результаты поиска

Содержание ML350 - ProLiant - G2

Отзывы:

Похожие инструкции для ML350 - ProLiant - G2

Бренды по названию

Популярные бренды

HP ML350 - ProLiant - G2, Руководство по техническому обслуживанию и ремонту

Результаты поиска

Содержание ML350 - ProLiant - G2

Отзывы:

Похожие инструкции для ML350 - ProLiant - G2

Бренды по названию

Популярные бренды