HP Jet Fusion 4200 Скачать руководство пользователя страница 28 | Manualshive

Страница: 28 / 56

background image

Doorway specifications (continued)

Length

2388 mm (94.02 in) with packaging

2283 mm (89.88 in) without packaging

The processing station can be moved on the pallet up or down a ramp of no more than 10° inclination.

Unpacking and moving the processing station

You are strongly recommended to unpack the processing station where it will be used, or as close to that
location as possible.

The space required for assembly is 5.5 × 3 m (217 × 118 in).

Moving equipment

If you are using the external tank and/or material loading tank, you will need a trolley to move it.

If you need to move the processing station after unpacking, take into account the following considerations:

●

Ground-floor installation: The processing station can be moved on wheels up or down a ramp of no more
than 10° inclination.

NOTE:

Remove the material-cartridge platform before moving the processing station up or down a ramp.

●

Above-ground installation: Use an elevator if the processing station can fit inside it while remaining
horizontal (without tilting the processing station), and if it can support the processing station’s weight.
Otherwise, you may need a crane; contact your reseller for more information.

CAUTION:

The processing station is heavy and can easily fall over. Moving it over a ramp or tilted floor increases

the risk. Move it smoothly, maintain safety precautions for people in the vicinity, and secure it against
overbalancing. Always move it parallel to its length.

CAUTION:

If you need to move the processing station on its wheels to its final position, move it down from the

pallet but do not remove all the transport protections and locks.

CAUTION:

Unloading and moving the processing station and all system components is the customer's

responsibility and not HP's. Failure to provide the required moving and lifting equipment could result in personal
injury or damage to the station during installation.

Load bearing

The load-bearing characteristics of the floor in the print-production area must be sufficient to withstand the
weight of your processing station. To calculate the load-bearing characteristics of the print-production floor,

consult a structural engineer.

Processing station weight

470 kg (1036 lb)

Processing station weight (loaded)

1070 kg (2359 lb), including the fully loaded processing station with storage tank and
mixer, one 300 L material cartridge, and a full external tank weighing 200 kg (441 lb)

Build unit weight (full)

185 kg (408 lb)

24

Chapter 3 Site preparation requirements for the processing station

ENWW

«
...
26
27
28
29
30
...
»

Содержание Jet Fusion 4200

























































Отзывы:

Нет отзывов

Похожие инструкции для Jet Fusion 4200

Бренд: IBM Страницы: 102

Бренд: Felix Storch Страницы: 39

Бренд: Felix Storch Страницы: 10

Бренд: quadient Страницы: 130

Бренд: Unimark Страницы: 36

Бренд: SEWOO Страницы: 17

Бренд: ABLE Systems Страницы: 12

Бренд: Oki Страницы: 143

Бренд: MIMAKI Страницы: 20

Бренд: TierTime Страницы: 35

Бренд: Delta OHM Страницы: 28

Бренд: Pringo Страницы: 2

Бренд: Panduit Страницы: 59

Бренд: Panduit Страницы: 39

Бренд: Whip Mix Страницы: 12

C11C418001 - Stylus C60 Inkjet Printer

Бренд: Epson Страницы: 64

C11C417001 - Stylus Photo 820 Color Inkjet Printer

Бренд: Epson Страницы: 2

C11C417001 - Stylus Photo 820 Color Inkjet Printer

Бренд: Epson Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды