HP J4899B Скачать руководство пользователя страница 84 | Manualshive

Страница: 84 / 116

background image

B-2

Switch Ports and Network Cables

S

wi

tc

h

P

o

rt

s

an

d N

e

two

rk

C

a

bl

es

Because of the increased speed provided by 1000Base-T (Gigabit-T), network
cable quality is more important than for either 10Base-T or 100Base-TX.
Cabling plants being used to carry 1000Base-T networking must comply with
the IEEE 802.3ab standards. In particular, the cabling must pass tests for
Attenuation, Near-End Crosstalk (NEXT), and Far-End Crosstalk (FEXT).
Additionally, unlike the cables for 100Base-TX, the 1000Base-T cables must
pass tests for Equal-Level Far-End Crosstalk (ELFEXT) and Return Loss.

When testing your cabling, be sure to include the patch cables that connect
the switch and other end devices to the patch panels on your site. The patch
cables are frequently overlooked when testing cable and they must also
comply with the cabling standards.

Fiber-Optic Cables

Port Type

Cable Specifications

Connector Type

Maximum Length

Gigabit-SX

62.5/125 mm or 50/125

μ

m (core/cladding)

diameter, graded-index, 850 nm, low metal
content, multimode fiber-optic cables,
complying with the ITU-T G.651 and ISO/IEC
793-2 Type A1b or A1a respectively.

LC

- Gigabit-SX

mini-GBIC

•

62.5

μ

m cable:

– 160 MHz*Km=220 meters
– 200 MHz*Km=275 meters

•

50

μ

m cable:

– 400 MHz*Km=500 meters
– 500 MHz*Km=550 meters

Gigabit-LX

9/125

μ

m (core/cladding) diameter, graded-

index, 1310 nm, low metal content, single
mode fiber-optic cables, complying with the
ITU-T G.652 and ISO/IEC 793-2 Type B1
standards.
OR
the multimode fiber-optic cables listed for
Gigabit-SX.

LC

- Gigabit-LX

mini-GBIC

•

Single-mode cable:

10 kilometers

•

Multimode cable:

550 meters

Note: To use multimode cables for Gigabit-LX, a mode conditioning patch cord may be needed - See

“Mode Conditioning Patch Cord for Gigabit-LX” on page B-3

for more information.

Gigabit-LH

9/125 mm (core/cladding) diameter, graded-
index, 1550 nm, low metal content, single
mode fiber-optic cables, complying with the
ITU-T G.652 and ISO/IEC 793-2 Type B1
standards.

LC

- Gigabit-LH

mini-GBIC

70 kilometers

Note:

Between the transmit and receive ends of the cable, at least 5db of attenuation is required for a

reliable connection. This is equivalent to 20 Km of the fiber-optic cable. For distances less than 20 Km,
you must add attenuators to bring the total attenuation to at least 5db. Most cable vendors carry
attenuators.

«
...
82
83
84
85
86
...
»

Содержание J4899B





















































































































Отзывы:

Нет отзывов

Похожие инструкции для J4899B

Бренд: KELCO Страницы: 22

Бренд: KELCO Страницы: 4

Бренд: Patton electronics Страницы: 104

Бренд: Valcom Страницы: 2

Бренд: West Mountain Radio Страницы: 10

Бренд: Clever Little Box Страницы: 15

Бренд: Tripp Lite Страницы: 12

Бренд: StarTech.com Страницы: 16

Бренд: Unipoe Страницы: 41

Бренд: Allen-Bradley Страницы: 2

AV Selector 310

Бренд: Hama Страницы: 21

Бренд: Cypress Страницы: 16

Бренд: TRENDnet Страницы: 2

kontron KSwitch D1 UGPD

Бренд: S&T Страницы: 40

Бренд: MicroNet Страницы: 123

Бренд: Lindy Страницы: 7

RPT-2012/P-4F-T-1 Series

Бренд: Subject Link Страницы: 2

Бренд: Extron electronics Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды