manualshive.com logo in svg

HP J4899B, Руководство по установке и началу работы

Поделиться
Скачать
HP J4899B Скачать руководство пользователя страница 59

2-39

Installing the Switch

Sample Network Topologies for PWR Switches

In

sta
llin
g

 th
e

 Sw

itc
h

Stacking the Switch

Switch 2600 and 2600-PWR Series devices can be connected together, through 
standard network connections, and managed through a single IP address. Up 
to 16 switches can be connected together in such a “virtual stack”.

You identify a Switch 2600 or 2600-PWR Series device as the “Commander” 
and give that switch an IP address. Up to 15 other switches in the network can 
then easily be configured as Members of the stack and managed through the 
Commander’s IP address. The management includes Telnet access and web 
browser interface access to the Commander and to each Member switch 
through the Commander.

For more information on stacking your switch, see the 

Management and 

Configuration Guide,

 which is on the Documentation CD-ROM that came 

with your switch.

Содержание J4899B





















































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды