HP J4861A Скачать руководство пользователя

Страница: 74 / 94

Switch Ports and Network Cables

Twisted-Pair Cable/Connector Pin-Outs

Crossover Twisted-Pair Cable for
10 Mbps or 100 Mbps Network Connection

The HP Auto-MDIX operation of the 10/100 ports on the switches also allows
you to use crossover cables for all network connections, to PCs, servers or
other end nodes, or to hubs or other switches.

If any of these ports are given a fixed configuration, for example 100 Mbps/
Full Duplex, the ports operate as MDI-X ports, and crossover cables

must

then used for connections to hubs or switches or other MDI-X network
devices.

Cable Diagram

N o t e

Pins 1 and 2 on connector “A”

must

be wired as a twisted pair to pins 3 and 6

on connector “B”.
Pins 3 and 6 on connector “A”

must

be wired as a twisted pair to pins 1 and 2

on connector “B”.
Pins 4, 5, 7, and 8 are not used in this application, although they may be wired
in the cable.

Pin Assignments

Switch End (MDI-X)

Hub or Switch Port, or Other
MDI-X Port End

ch Ports and

Netw

ork

Cabl

Signal

Pins

Signal

transmit -

receive -

transmit -

B-6

Содержание J4861A































































































Результаты поиска

Содержание J4861A

Отзывы:

Похожие инструкции для J4861A

Бренды по названию

Популярные бренды

HP J4861A, Руководство по установке и началу работы

Результаты поиска

Содержание J4861A

Отзывы:

Похожие инструкции для J4861A

Бренды по названию

Популярные бренды