HP Integrity NonStop i NS2300 Скачать руководство пользователя страница 53 | Manualshive

Страница: 53 / 81

HP Integrity NonStop i NS2300 Скачать руководство пользователя страница 53

Rack Stability

Rack stabilizers are required when you have less than four racks bayed together.

NOTE:

Rack stability is of special concern when equipment is routinely installed, removed, or

accessed within the rack. Stability is addressed through the use of leveling feet, baying kits, fixed
stabilizers, and/or ballast. Use baying kits to bay Intelligent racks to Intelligent racks of the same
height. In all cases, a rack cannot be bayed with another rack of a different height.

For information about best practices for racks or grounding the racks using a rack ground bonding
kit, your service provider can refer to:

•

HP Rack Options Installation Guide

•

http://www.hpe.com/support/Intelligent_Series_Rack_Manuals

Environmental Specifications

Heat Dissipation Specifications and Worksheet

Total (BTU/hour)

Unit Heat
(BTU/hour)
Maximum

Unit Heat
(BTU/hour) Typical

Number Installed

Enclosure Type

1212

924

16 GB CPU

1240

938

32 GB CPU

1268

952

48 GB CPU

1112

894

VIO enclosure

768

461

G6 Storage CLIM

682

444

G6 IP or Telco CLIM

699

419

Gen8 Storage CLIM

692

399

Gen8 Networking
CLIM, 5 copper ports
(IP or Telco)

716

419

Gen8 Networking
CLIM, 3 copper
ports/2 optical ports
(IP or Telco)

614

443

Gen9 Networking
CLIM, 5 copper ports
(IP or Telco)

631

461

Gen9 Networking
CLIM, 3 copper
ports/2 optical ports
(IP or Telco)

427

256

D2700 SAS disk
enclosure (no disks)

427

256

D3700 SAS disk
enclosure (no disks)

30

17

SAS 2.5 in. 10k rpm
disk drive

24

14

SAS 2.5 in. 15k rpm
disk drive

Rack Stability

53

«
...
51
52
53
54
55
...
»

Содержание Integrity NonStop i NS2300


















































































Отзывы:

Нет отзывов