HP HPE Synergy 12000 Frame Скачать руководство пользователя страница 38

Страница: 38 / 183

NVDIMM Function LED patterns

For the purpose of this table, the NVDIMM-N LED operates as follows:

Solid indicates that the LED remains in the on state.

Flashing indicates that the LED is on for 2 seconds and off for 1 second.

Fast-flashing indicates that the LED is on for 300 ms and off for 300 ms.

State

Definition

NVDIMM-N Function LED

The restore operation is in progress.

Flashing

The restore operation is successful.

Solid or On

Erase is in progress.

Flashing

The erase operation is successful.

Solid or On

The NVDIMM-N is armed, and the NVDIMM-N is in normal operation.

Solid or On

The save operation is in progress.

Flashing

The NVDIMM-N finished saving and battery is still turned on (12 V still
powered).

Solid or On

The NVDIMM-N has an internal error or a firmware update is in
progress. For more information about an NVDIMM-N internal error, see
the IML.

Fast-flashing

NVDIMM Function LED patterns

Содержание HPE Synergy 12000 Frame
























































































































































































Результаты поиска

Содержание HPE Synergy 12000 Frame

Отзывы:

Бренды по названию

Популярные бренды

HP HPE Synergy 12000 Frame, Руководство по установке и настройке

Результаты поиска

Содержание HPE Synergy 12000 Frame

Отзывы:

Бренды по названию

Популярные бренды