HP HPE Synergy 12000 Frame Скачать руководство пользователя страница 160

Страница: 160 / 183

Accessing the

Accessing the HPE

HPE OneView Maintenance Console

OneView Maintenance Console from the

from the frame link module

frame link module

Procedure

1. Connect locally to the HPE Synergy Console.

2. Select the Screen

Screen icon at the top right of the page.

3. Select an HPE Synergy Composer from the Appliances menu.

A blank text window appears.

4. Press Enter

Enter.

5. At the login prompt, log in using the following username:

maintenance

The HPE OneView Maintenance Console opens.

For additional instructions on using the HPE OneView Maintenance Console, see the HPE OneView User Guide for HPE Synergy on the
Hewlett Packard Enterprise

Hewlett Packard Enterprise website

website.

Accessing the HPE OneView Maintenance Console from the frame link module

160

Содержание HPE Synergy 12000 Frame
























































































































































































Результаты поиска

Содержание HPE Synergy 12000 Frame

Отзывы:

Бренды по названию

Популярные бренды

HP HPE Synergy 12000 Frame, Руководство по установке и настройке

Результаты поиска

Содержание HPE Synergy 12000 Frame

Отзывы:

Бренды по названию

Популярные бренды