HP HPE FlexFabric 5930 Скачать руководство пользователя страница 65

Страница: 65 / 73

Table 26 Management Ethernet port LED description for the HPE 5930-32 QSFP+/HPE
5930-32 QSFP+ TAA/HPE 5930-4Slot/HPE 5930-4Slot TAA switches

LED mark

Status

Description

LINK

Off

The management Ethernet port is not connected.

Steady green

The management Ethernet port is operating at 10/100/1000 Mbps.

ACT

Off

The management Ethernet port is not receiving or sending data.

Flashing yellow

The management Ethernet port is sending or receiving data.

The HPE 5930-2Slot+2QSFP+/HPE 5930-2Slot+2QSFP+ TAA switch provides a LINK/ACT LED for
the management Ethernet port.

Table 27 Management Ethernet port LED description for the HPE 5930-2Slot+2QSFP+/HPE
5930-2Slot+2QSFP+ TAA switch

LED mark

Status

Description

MGMT
LINK/ACT

Steady green

The management Ethernet port is operating at 10/100/1000 Mbps.

Flashing green

The management Ethernet port is receiving or sending data.

Off

The management Ethernet port is not connected.

1/10GBase-T autosensing Ethernet port LEDs

Table 28 1/10GBase-T autosensing Ethernet port LED description

Status Description

Steady green

The port has a link and is operating at 10 Gbps.

Flashing green

The port is sending or receiving data at 10 Gbps.

Steady yellow

The port has a link and is operating at 1 Gbps.

Flashing yellow

The port is sending or receiving data at 1 Gbps.

Off

No link is present on the port.

Fan tray alarm LEDs

The LSWM1BFANSC and LSWM1BFANSCB fan trays provide an Alarm LED.

Table 29 LSWM1BFANSC and LSWM1BFANSCB fan tray alarm LED description

Status Description

The fan tray is faulty.

Off

The fan tray is operating correctly.

Содержание HPE FlexFabric 5930










































































Результаты поиска

Содержание HPE FlexFabric 5930

Отзывы:

Похожие инструкции для HPE FlexFabric 5930

Бренды по названию

Популярные бренды

HP HPE FlexFabric 5930, Руководство по установке

Результаты поиска

Содержание HPE FlexFabric 5930

Отзывы:

Похожие инструкции для HPE FlexFabric 5930

Бренды по названию

Популярные бренды