HP HPE Alletra 6010 Скачать руководство пользователя страница 49

Страница: 49 / 117

Array information on the label includes:

•

Serial number

•

Controller A / Controller B location

•

Port mappings

The QR code on the label leads to the Welcome Center on HPE InfoSight. Visit the Welcome Center for help setting up your
HPE storage array.

Find the Serial Number of an Array Using the GUI

Procedure

1. In the GUI, choose Hardware.

2. Click the link of the array you want.

3. Look in the Properties section for the serial number.

Find the Serial Number of an Array Using the CLI

Procedure

1. Find the serial number of an array.

shelf --array array name --list

2. Look for the serial number in the list of information.

Example

$ shelf --array rackarray3 --list

Check Array Model, OS Version, and Operating State Using the GUI

Obtain information about your array before performing general maintenance, software updates, hardware replacements, or
hardware upgrades.

Array Components 49

Documentation Feedback: [email protected]

Содержание HPE Alletra 6010






















































































































Результаты поиска

Содержание HPE Alletra 6010

Отзывы:

Похожие инструкции для HPE Alletra 6010

Бренды по названию

Популярные бренды

HP HPE Alletra 6010, Руководство по оборудованию

Результаты поиска

Содержание HPE Alletra 6010

Отзывы:

Похожие инструкции для HPE Alletra 6010

Бренды по названию

Популярные бренды