manualshive.com logo in svg

HP G2 Series, Руководство по установке

Поделиться
Скачать
HP G2 Series Скачать руководство пользователя страница 76

IMPORTANT: Access to some updates might require product entitlement when accessed through the Hewlett Packard
Enterprise Support Center. You must have an HPE Passport set up with relevant entitlements.

Customer self repair

Hewlett Packard Enterprise customer self repair (CSR) programs allow you to repair your product. If a CSR part needs to be
replaced, it will be shipped directly to you so that you can install it at your convenience. Some parts do not qualify for CSR.
Your Hewlett Packard Enterprise authorized service provider will determine whether a repair can be accomplished by CSR.

For more information about CSR, contact your local service provider.

Websites

General websites
Hewlett Packard Enterprise Support Center

www.hpe.com/support/hpesc

Contact Hewlett Packard Enterprise Worldwide

www.hpe.com/assistance

Insight Remote Support

www.hpe.com/info/insightremotesupport/docs

For additional websites, see 

Support and other resources.

Warranty information

To view the warranty information for your product, see the links provided below:

HPE ProLiant and IA-32 Servers and Options

https://www.hpe.com/support/ProLiantServers-Warranties

HPE Enterprise and Cloudline Servers

https://www.hpe.com/support/EnterpriseServers-Warranties

HPE Storage Products

https://www.hpe.com/support/Storage-Warranties

HPE Networking Products

https://www.hpe.com/support/Networking-Warranties

Warranty information

HPE ProLiant and x86 Servers and Options

http://www.hpe.com/support/ProLiantServers-Warranties

HPE Enterprise Servers

http://www.hpe.com/support/EnterpriseServers-Warranties

HPE Storage Products

http://www.hpe.com/support/Storage-Warranties

HPE Networking Products

http://www.hpe.com/support/Networking-Warranties

Support and other resources

76

Содержание G2 Series















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды