HP FlexNetwork 5130 HI series Скачать руководство пользователя страница 97

Страница: 97 / 306

Field Description

Selected Ports

Total number of Selected ports.

Unselected Ports

Total number of Unselected ports.

Individual Ports

Total number of Individual ports.

Share Type

Load sharing type.

display link-aggregation verbose

Use

display link-aggregation verbose

to display detailed information about the aggregation

groups that correspond to the specified aggregate interfaces.

Syntax

display link-aggregation

verbose

[

bridge-aggregation

[

interface-number

] ]

Views

Any view

Predefined user roles

network-admin

network-operator

Parameters

bridge-aggregation

: Specifies Layer 2 aggregate interfaces.

interface-number

: Specifies an existing aggregate interface by its number.

Usage guidelines

If you specify the

bridge-aggregation

keyword but do not specify an interface number, the

command displays detailed information about all Layer 2 aggregation groups.

If you do not specify an aggregate interface type, the command displays detailed information about
all aggregation groups.

The

bridge-aggregation

keyword is available only when Layer 2 aggregate interfaces exist on the

device.

Examples

# Display detailed information about Layer 2 aggregation group 10, which is a dynamic aggregation
group.

<Sysname> display link-aggregation verbose bridge-aggregation 10

Loadsharing Type: Shar -- Loadsharing, NonS -- Non-Loadsharing

Port Status: S -- Selected, U -- Unselected, I -- Individual

Flags: A -- LACP_Activity, B -- LACP_Timeout, C -- Aggregation,

D -- Synchronization, E -- Collecting, F -- Distributing,

G -- Defaulted, H -- Expired

Aggregate Interface: Bridge-Aggregation10

Aggregation Mode: Dynamic

Loadsharing Type: Shar

System ID: 0x8000, 000f-e267-6c6a

Local:

Port Status Priority Oper-Key Flag

Содержание FlexNetwork 5130 HI series



















































































































































































































































































































Результаты поиска

Содержание FlexNetwork 5130 HI series

Отзывы:

Похожие инструкции для FlexNetwork 5130 HI series

Бренды по названию

Популярные бренды

HP FlexNetwork 5130 HI series, Справочник по командам

Результаты поиска

Содержание FlexNetwork 5130 HI series

Отзывы:

Похожие инструкции для FlexNetwork 5130 HI series

Бренды по названию

Популярные бренды