manualshive.com logo in svg

HP FlexNetwork 5130 HI series, Справочник по командам

Поделиться
Скачать
HP FlexNetwork 5130 HI series Скачать руководство пользователя страница 64

 

56 

MAC address table commands 

This document covers the configuration of unicast MAC address entries, including static, dynamic, 
blackhole, and multiport unicast MAC address entries. For more information about configuring static 
multicast MAC address entries, see 

IP Multicast Configuration Guide

. 

display mac-address 

Use 

display mac

-

address 

to display MAC address entries.  

Syntax 

display mac-address

 [ 

mac

-

address

 [ 

vlan

 

vlan-id

 ] | [ [ 

dynamic

 | 

static

 ] [ 

interface interface-type 

interface-number

 ] | 

blackhole

 | 

multiport

 ] [ 

vlan

 

vlan-id

 ] [ 

count

 ] ] 

Views 

Any view 

Predefined user roles 

network-admin 

network-operator 

Parameters 

mac

-

address

: Specifies a MAC address in the format of H-H-H. When entering a MAC address, you 

can omit the leading zeros in each H section. For example, enter f-e2-1 for 000f-00e2-0001.  

vlan vlan

-

id

: Specifies a VLAN by its ID in the range of 1 to 4094.  

dynamic

: Displays dynamic MAC address entries. 

static

: Displays static MAC address entries.  

interface interface

-

type interface

-

number

: Specifies an interface by its type and number.  

blackhole

: Displays blackhole MAC address entries. 

multiport

: Displays multiport unicast MAC address entries.  

count

: Displays only the number of MAC address entries that match all entry attributes you specify in 

the command. Detailed information about MAC address entries is not displayed. For example, you 
can use the 

display mac-address

 

vlan 20 dynamic count

 command to display the number of 

dynamic entries for VLAN 20. If you do not specify an entry attribute, the command displays the 
number of entries in the MAC address table. If you do not specify this keyword, the command 
displays detailed information about the specified MAC address entries. 

Usage guidelines 

A MAC address entry includes a destination MAC address, an outgoing interface, and a VLAN ID.  

If you do not specify any parameters, the command displays all MAC address entries. 

This command displays dynamic MAC address entries for an aggregate interface only when the 
aggregate interface has at least one Selected member port. 

Examples 

# Display MAC address entries for VLAN 100.  

<Sysname> display mac-address vlan 100 

MAC Address      VLAN ID    State            Port/NickName            Aging 

0001-0101-0101   100        Multiport        GE1/0/1                    N 

                                             GE1/0/2 

Содержание FlexNetwork 5130 HI series



















































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды