HP FlexNetwork 5130 HI series Скачать руководство пользователя страница 59

Страница: 59 / 306

shutdown

Use

shutdown

to shut down a loopback interface.

Use

undo shutdown

to bring up a loopback interface.

Syntax

shutdown

undo shutdown

Default

A loopback interface is up.

Views

Loopback interface view

Predefined user roles

network-admin

Usage guidelines

Use the

shutdown

command with caution, because the command disconnects the connection of the

interface and disables the interface from communicating.

Examples

# Shut down interface loopback 1.

<Sysname> system-view

[Sysname] interface loopback 1

[Sysname-LoopBack1] shutdown

Содержание FlexNetwork 5130 HI series



















































































































































































































































































































Результаты поиска

Содержание FlexNetwork 5130 HI series

Отзывы:

Бренды по названию

Популярные бренды

HP FlexNetwork 5130 HI series, Справочник по командам

Результаты поиска

Содержание FlexNetwork 5130 HI series

Отзывы:

Бренды по названию

Популярные бренды