HP FlexNetwork 5130 HI series Скачать руководство пользователя страница 28

Страница: 28 / 306

Syntax

interface interface-type

interface-number

Views

System view

Predefined user roles

network-admin

Parameters

interface-type

: Specifies an interface type.

interface-number

: Specifies an interface number.

Examples

# Enter GigabitEthernet 1/0/1 interface view.

<Sysname> system-view

[Sysname] interface gigabitethernet 1/0/1

[Sysname-GigabitEthernet1/0/1]

jumboframe enable

Use

jumboframe enable

to allow jumbo frames within the specified length to pass through.

Use

undo jumboframe enable

to prevent jumbo frames from passing through.

Syntax

jumboframe enable

[

value

]

undo jumboframe enable

Default

The device allows jumbo frames within 10000 bytes to pass through.

Views

Ethernet interface view

Predefined user roles

network-admin

Parameters

value

: Sets the maximum length of Ethernet frames that are allowed to pass through. The value

range is 1536 to 10000 bytes.

Usage guidelines

If you set the

value

argument multiple times, the most recent configuration takes effect.

Examples

# Enable jumbo frames to pass through GigabitEthernet 1/0/1.

<Sysname> system-view

[Sysname] interface gigabitethernet 1/0/1

[Sysname-GigabitEthernet1/0/1] jumboframe enable

Содержание FlexNetwork 5130 HI series



















































































































































































































































































































Результаты поиска

Содержание FlexNetwork 5130 HI series

Отзывы:

Бренды по названию

Популярные бренды

HP FlexNetwork 5130 HI series, Справочник по командам

Результаты поиска

Содержание FlexNetwork 5130 HI series

Отзывы:

Бренды по названию

Популярные бренды