HP FlexNetwork 5130 HI series Скачать руководство пользователя страница 24

Страница: 24 / 306

Parameters

interface-type

: Specifies an interface type. If you do not specify an interface type, this command

displays information about dropped packets on all the interfaces on the device.

interface-number

: Specifies an interface number. If you specify an interface type only, this command

displays information about dropped packets on the specified type of interfaces.

summary

: Displays the summary of dropped packets on all interfaces.

Examples

# Display information about dropped packets on GigabitEthernet 1/0/1.

<Sysname> display packet-drop interface gigabitethernet 1/0/1

GigabitEthernet1/0/1:

Packets dropped due to full GBP or insufficient bandwidth: 301

Packets dropped due to Fast Filter Processor (FFP): 261

Packets dropped due to STP non-forwarding state: 321

# Display the summary of dropped packets on all interfaces.

<Sysname> display packet-drop summary

All interfaces:

Packets dropped due to full GBP or insufficient bandwidth: 301

Packets dropped due to Fast Filter Processor (FFP): 261

Packets dropped due to STP non-forwarding state: 321

Table 6 Command output

Field Description

Packets dropped due to full GBP or insufficient
bandwidth

Packets that are dropped because the buffer is
used up or the bandwidth is insufficient.

Packets dropped due to Fast Filter Processor (FFP)

Packets that are filtered out.

Packets dropped due to STP non-forwarding state

Packets that are dropped because STP is in the
non-forwarding state.

duplex

Use

duplex

to set the duplex mode for an Ethernet interface.

Use

undo duplex

to restore the default duplex mode of the Ethernet interface.

Syntax

duplex

{

auto

full

half

}

undo duplex

Default

Ethernet interfaces autonegotiate the duplex mode.

Views

Ethernet interface view

Predefined user roles

network-admin

Parameters

auto

: Configures the interface to autonegotiate the duplex mode with the peer.

Содержание FlexNetwork 5130 HI series



















































































































































































































































































































Результаты поиска

Содержание FlexNetwork 5130 HI series

Отзывы:

Похожие инструкции для FlexNetwork 5130 HI series

Бренды по названию

Популярные бренды

HP FlexNetwork 5130 HI series, Справочник по командам

Результаты поиска

Содержание FlexNetwork 5130 HI series

Отзывы:

Похожие инструкции для FlexNetwork 5130 HI series

Бренды по названию

Популярные бренды