HP FlexNetwork 5130 HI series Скачать руководство пользователя страница 233

Страница: 233 / 306

225

voice-vlan enable

Use

voice-vlan enable

to enable the voice VLAN feature and configure a VLAN as the voice VLAN

for a port.

Use

undo voice-vlan enable

to disable the voice VLAN feature on a port.

Syntax

voice-vlan

vlan-id enable

undo voice-vlan

[

vlan-id

]

enable

Default

The voice VLAN feature is disabled on ports.

Views

Layer 2 Ethernet interface view

Predefined user roles

network-admin

Parameters

vlan-id

: Specifies a voice VLAN ID in the range of 2 to 4094.

Usage guidelines

Use this command only on a hybrid or trunk port operating in automatic voice VLAN assignment
mode.

Examples

# Enable the voice VLAN feature and configure VLAN 2 as the voice VLAN on GigabitEthernet 1/0/1.

<Sysname> system-view

[Sysname] interface gigabitethernet 1/0/1

[Sysname-GigabitEthernet1/0/1] voice-vlan 2 enable

Related commands

display voice-vlan state

voice-vlan mode auto

voice-vlan mac-address

Use

voice-vlan mac-address

to configure the OUI address information for voice packet

identification.

Use

undo voice-vlan mac-address

to delete an OUI address.

Syntax

voice-vlan mac-address

mac-address

mask

oui-mask

[

description text

]

undo voice-vlan mac-address

oui

Default

System default OUI addresses exist.

Table 50 System default OUI addresses

Number OUI

address

Vendor

1 0001-E300-0000

Siemens

phone

Содержание FlexNetwork 5130 HI series



















































































































































































































































































































Результаты поиска

Содержание FlexNetwork 5130 HI series

Отзывы:

Похожие инструкции для FlexNetwork 5130 HI series

Бренды по названию

Популярные бренды

HP FlexNetwork 5130 HI series, Справочник по командам

Результаты поиска

Содержание FlexNetwork 5130 HI series

Отзывы:

Похожие инструкции для FlexNetwork 5130 HI series

Бренды по названию

Популярные бренды