HP FlexNetwork 5130 HI series Скачать руководство пользователя страница 231

Страница: 231 / 306

223

0001-e300-0000 ffff-ff00-0000 Siemens phone

0003-6b00-0000 ffff-ff00-0000 Cisco phone

0004-0d00-0000 ffff-ff00-0000 Avaya phone

000f-e200-0000 ffff-ff00-0000 H3C Aolynk phone

0060-b900-0000 ffff-ff00-0000 Philips/NEC phone

00d0-1e00-0000 ffff-ff00-0000 Pingtel phone

00e0-7500-0000 ffff-ff00-0000 Polycom phone

00e0-bb00-0000 ffff-ff00-0000 3Com phone

Table 48 Command output

Field Description

OUI address

OUI address allowed on the device.

Mask

Mask of the OUI address.

Description

Description of the OUI address.

Related commands

voice-vlan mac-address

display voice-vlan state

Use

display voice-vlan state

to display voice VLAN information.

Syntax

display voice-vlan state

Views

Any view

Predefined user roles

network-admin

network-operator

Examples

# Display voice VLAN information.

<Sysname> display voice-vlan state

Current voice VLANs: 1

Voice VLAN security mode: Security

Voice VLAN aging time: 1440 minutes

Voice VLAN enabled ports and their modes:

Port VLAN Mode CoS DSCP

GigabitEthernet1/0/1 111 Auto 6 46

Table 49 Command output

Field Description

Current Voice VLANs

Number of existing voice VLANs.

Voice VLAN security mode

Voice VLAN mode:

•

Security.

•

Normal.

Содержание FlexNetwork 5130 HI series



















































































































































































































































































































Результаты поиска

Содержание FlexNetwork 5130 HI series

Отзывы:

Бренды по названию

Популярные бренды

HP FlexNetwork 5130 HI series, Справочник по командам

Результаты поиска

Содержание FlexNetwork 5130 HI series

Отзывы:

Бренды по названию

Популярные бренды