HP FlexNetwork 5130 HI series Скачать руководство пользователя страница 215

Страница: 215 / 306

207

[Sysname] interface gigabitethernet 1/0/1

[Sysname-GigabitEthernet1/0/1] port private-vlan host

[Sysname-GigabitEthernet1/0/1] display this

interface GigabitEthernet1/0/1

port private-vlan host

return

The output show that GigabitEthernet 1/0/1 is operating in bridge mode and is a host port.

# Assign GigabitEthernet 1/0/1 to VLAN 20, and then verify the configuration.

[Sysname-GigabitEthernet1/0/1] port access vlan 20

[Sysname-GigabitEthernet1/0/1] display this

interface GigabitEthernet1/0/1

port private-vlan host

port link-type hybrid

undo port hybrid vlan 1

port hybrid vlan 2 20 untagged

port hybrid pvid vlan 20

return

The output shows that:

•

The port link type of GigabitEthernet 1/0/1 is hybrid and its PVID is VLAN 20.

•

GigabitEthernet 1/0/1 is an untagged member of secondary VLAN 20 and primary VLAN 2.

Related commands

•

port private-vlan promiscuous

•

port private-vlan trunk promiscuous

•

port private-vlan trunk secondary

•

private-vlan

(VLAN view)

•

private-vlan

primary

port private-vlan promiscuous

Use

port private-vlan

promiscuous

to configure a port as a promiscuous port of the specified

VLAN and assign the port to the VLAN.

Use

undo port private-vlan

to restore the default.

Syntax

port private-vlan

vlan-id

promiscuous

undo port private-vlan

Default

A port is not a promiscuous port of any VLAN.

Views

Layer 2 Ethernet interface view, Layer 2 aggregate interface view

Содержание FlexNetwork 5130 HI series



















































































































































































































































































































Результаты поиска

Содержание FlexNetwork 5130 HI series

Отзывы:

Бренды по названию

Популярные бренды

HP FlexNetwork 5130 HI series, Справочник по командам

Результаты поиска

Содержание FlexNetwork 5130 HI series

Отзывы:

Бренды по названию

Популярные бренды