HP FlexNetwork 5130 HI series Скачать руководство пользователя страница 210

Страница: 210 / 306

202

Related commands

•

subvlan

•

supervlan

subvlan

Use

subvlan

to associate a super VLAN with the specified sub-VLANs.

Use

undo subvlan

to dissociate sub-VLANs from a super VLAN.

Syntax

subvlan vlan-id-list

undo subvlan

[

vlan-id-list

]

Default

A super VLAN is not associated with any sub-VLANs.

Views

VLAN view

Predefined user roles

network-admin

Parameters

vlan-id-list

: Specifies a space-separated list of up to 10 sub-VLAN items. Each item specifies a

sub-VLAN ID or a range of sub-VLAN IDs in the form of

vlan-id1

vlan-id2

. The value range for

sub-VLAN IDs is 1 to 4094. The value for the

vlan-id2

argument must be equal to or greater than the

value for the

vlan-id1

argument.

Usage guidelines

Make sure sub-VLANs already exist before associating them with a super VLAN.

You can add ports to and remove ports from a sub-VLAN that is already associated with a super
VLAN.

When you use the

undo subvlan

command, follow these guidelines:

•

If you do not specify the

vlan-id-list

argument, this command dissociates all sub-VLANs from

the current super VLAN.

•

If you specify the

vlan-id-list

argument, this command dissociates the specified sub-VLANs

from the current super VLAN.

Examples

# Associate super VLAN 10 with sub-VLANs 3, 4, 5, and 9.

<Sysname> system-view

[Sysname] vlan 10

[Sysname-vlan10] supervlan

[Sysname-vlan10] subvlan 3 to 5 9

Related commands

•

display

supervlan

•

supervlan

Содержание FlexNetwork 5130 HI series



















































































































































































































































































































Результаты поиска

Содержание FlexNetwork 5130 HI series

Отзывы:

Похожие инструкции для FlexNetwork 5130 HI series

Бренды по названию

Популярные бренды

HP FlexNetwork 5130 HI series, Справочник по командам

Результаты поиска

Содержание FlexNetwork 5130 HI series

Отзывы:

Похожие инструкции для FlexNetwork 5130 HI series

Бренды по названию

Популярные бренды