HP FlexNetwork 5130 HI series Скачать руководство пользователя страница 208

Страница: 208 / 306

200

Super VLAN commands

display supervlan

Use

display supervlan

to display information about super VLANs and their associated sub-VLANs.

Syntax

display supervlan

[

supervlan-id

]

Views

Any view

Predefined user roles

network-admin

network-operator

Parameters

supervlan-id

: Specifies a super VLAN ID in the range of 1 to 4094. If you do not specify a super VLAN

ID, this command displays information about all super VLANs and their associated sub-VLANs.

Examples

# Display information about super VLAN 2 and its associated sub-VLANs.

<Sysname> display supervlan 2

Super VLAN ID: 2

Sub-VLAN ID: 3-5

VLAN ID: 2

VLAN type: Static

It is a super VLAN.

Route interface: Configured

IPv4 address: 10.153.17.41

IPv4 subnet mask: 255.255.252.0

IPv6 global unicast addresses:

2001::1, subnet is 2001::/64 [TENTATIVE]

Description: VLAN 0002

Name: VLAN 0002

Tagged ports: None

Untagged ports: None

VLAN ID: 3

VLAN type: Static

It is a sub VLAN.

Route interface: Configured

IPv4 address: 10.153.17.41

IPv4 subnet mask: 255.255.252.0

IPv6 global unicast addresses:

2001::1, subnet is 2001::/64 [TENTATIVE]

Description: VLAN 0003

Name: VLAN 0003

Содержание FlexNetwork 5130 HI series



















































































































































































































































































































Результаты поиска

Содержание FlexNetwork 5130 HI series

Отзывы:

Бренды по названию

Популярные бренды

HP FlexNetwork 5130 HI series, Справочник по командам

Результаты поиска

Содержание FlexNetwork 5130 HI series

Отзывы:

Бренды по названию

Популярные бренды