HP FlexNetwork 5130 HI series Скачать руководство пользователя страница 202

Страница: 202 / 306

194

Table 44 Command output

Field Description

VLAN ID

ID of the protocol-based VLAN.

Protocol index

Protocol template index.

Protocol type

Protocol type or encapsulation format specified by the protocol
template.

Related commands

•

display protocol-vlan interface

•

port

hybrid

protocol-vlan

•

protocol-vlan

port hybrid protocol-vlan

Use

port hybrid protocol-vlan

to associate a hybrid port with the specified protocols in a VLAN.

Use

undo

port hybrid protocol-vlan

to remove the association.

Syntax

port hybrid protocol-vlan

vlan

vlan-id

{

protocol-index

[

protocol-end

] |

all

}

undo hybrid protocol-vlan

{

vlan

vlan-id

{

protocol-index

[

protocol-end

] |

all

} |

all

}

Default

A port is not associated with any protocol-based VLANs.

Views

Layer 2 Ethernet interface view, Layer 2 aggregate interface view,

Predefined user roles

network-admin

Parameters

vlan

vlan

: Specifies a VLAN by its ID in the range of 1 to 4094.

protocol-index

: Specifies a beginning protocol template index in the range of 0 to 65535.

to protocol-end

: Specifies an end protocol template index of a protocol template range,

in the range

of 0 to 65535. The value for the

protocol-end

argument must be greater than or equal to the

beginning protocol template index.

all

: Specifies all protocol templates.

Usage guidelines

Before you use this command, perform the following tasks:

•

Create a VLAN and associate it with specified protocols.

•

Configure the port link type as hybrid.

•

Configure the port to allow the protocol-based VLAN to pass through.

When you execute the

undo port hybrid protocol-vlan

command on a port, follow these

guidelines:

•

If you specify both the

vlan-id

argument and the

all

keyword, this command disassociates the

port from all protocol templates of the specified VLAN.

Содержание FlexNetwork 5130 HI series



















































































































































































































































































































Результаты поиска

Содержание FlexNetwork 5130 HI series

Отзывы:

Бренды по названию

Популярные бренды

HP FlexNetwork 5130 HI series, Справочник по командам

Результаты поиска

Содержание FlexNetwork 5130 HI series

Отзывы:

Бренды по названию

Популярные бренды