HP FlexNetwork 5130 HI series Скачать руководство пользователя страница 201

Страница: 201 / 306

193

Table 43 Command output

Field Description

VLAN ID

ID of the protocol-based VLAN.

Protocol index

Protocol template index.

Protocol type

Protocol type specified by the protocol template.

If you do not specify the protocol type, this field displays

N/A

Status

Whether the protocol-based VLAN has taken effect:

•

Active

—The protocol-based VLAN has taken effect.

•

Inactive

—The protocol-based VLAN has not taken effect.

Related commands

•

display

protocol-vlan

vlan

•

port

hybrid

protocol-vlan

•

protocol-vlan

display protocol-vlan vlan

Use

display protocol-vlan vlan

to display information about protocol-based VLANs.

Syntax

display protocol-vlan vlan

{

vlan

id1

[

to vlan

id2

]

all

}

Views

Any view

Predefined user roles

network-admin

network-operator

Parameters

vlan

id1

: Specifies a protocol-based VLAN ID in the range of 1 to 4094.

vlan

id1 to vlan

id2:

Specifies a VLAN ID range. Both the

vlan-id1

and the

vlan-id2

arguments are in

the range of 1 to 4094. The value for the

vlan-id2

argument must be equal to or greater than the

value for the

vlan-id1

argument.

all

: Specifies all protocol-based VLANs.

Examples

# Displays information about all protocol-based VLANs.

<Sysname> display protocol-vlan vlan all

VLAN ID: 2

Protocol index Protocol type

0 IPv4

65535 IPv6

VLAN ID: 3

Protocol index Protocol type

0 IPv4

65535 LLC DSAP 0x11 SSAP 0x22

Содержание FlexNetwork 5130 HI series



















































































































































































































































































































Результаты поиска

Содержание FlexNetwork 5130 HI series

Отзывы:

Бренды по названию

Популярные бренды

HP FlexNetwork 5130 HI series, Справочник по командам

Результаты поиска

Содержание FlexNetwork 5130 HI series

Отзывы:

Бренды по названию

Популярные бренды