manualshive.com logo in svg

HP FlexNetwork 5130 HI series, Справочник по командам

Поделиться
Скачать
HP FlexNetwork 5130 HI series Скачать руководство пользователя страница 200

 

192 

[Sysname-GigabitEthernet1/0/1] port hybrid ip-subnet-vlan vlan 3 

# Associate the Layer 2 aggregate interface Bridge-Aggregation 1 with the IP subnet-based VLAN 3.  

<Sysname> system-view 

[Sysname] vlan 3 

[Sysname-vlan3] ip-subnet-vlan ip 192.168.1.0 255.255.255.0 

[Sysname-vlan3] quit 

[Sysname] interface bridge-aggregation 1 

[Sysname-Bridge-Aggregation1] port link-type hybrid 

[Sysname-Bridge-Aggregation1] port hybrid vlan 3 untagged 

[Sysname-Bridge-Aggregation1] port hybrid ip-subnet-vlan vlan 3 

Related commands 

•

 

display ip-subnet-vlan interface 

•

 display 

ip-subnet-vlan 

vlan 

•

 ip-subnet-vlan 

Protocol-based VLAN commands 

display protocol-vlan interface 

Use 

display protocol-vlan interface 

to display information about protocol-based VLANs for the 

specified ports. 

Syntax 

display protocol-vlan interface

 { 

interface-type interface-number1

 [ 

to

 

interface-type 

interface-number2

 ] | 

all 

} 

Views 

Any view 

Predefined user roles 

network-admin 

network-operator 

Parameters 

interface-type interface-number1

: Specifies an interface by its type and number. 

interface-type interface-number1

 

to

 

interface-type interface-number2

: Specifies an interface range. 

all

: Displays information about protocol-based VLANs on all ports. 

Examples 

# Display protocol-based VLAN information on GigabitEthernet 1/0/1. 

<Sysname> display protocol-vlan interface gigabitethernet 1/0/1 

 Interface: GigabitEthernet1/0/1 

  VLAN ID  Protocol index  Protocol type             Status 

  2        0               IPv6                      Active 

  2        1               N/A                       Inactive 

  4094     65535           IPv4                      Inactive 

Содержание FlexNetwork 5130 HI series



















































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды