HP FlexNetwork 5130 HI series Скачать руководство пользователя страница 197

Страница: 197 / 306

189

Examples

# Display IP subnet-based VLANs on GigabitEthernet 1/0/1.

<Sysname> display ip-subnet-vlan interface gigabitethernet 1/0/1

Interface: GigabitEthernet1/0/1

VLAN ID Subnet index IP address Subnet mask Status

3 0 192.168.1.0 255.255.255.0 Active

4 N/A N/A N/A Inactive

4094 65535 172.16.1.1 255.255.0.0 Inactive

Table 41 Command output

Field Description

VLAN ID

ID of the IP subnet-based VLAN.

Subnet index

Index of the IP subnet.

If no IP subnet-based VLAN is configured, this field displays

N/A

IP address

IP address of the subnet. It can be an IP address or a subnet address.

If no IP subnet address is configured for the VLAN, this field displays

N/A

Subnet mask

Mask of the IP subnet.

If no subnet mask is configured for the VLAN, this field displays

N/A

Status

Whether the IP subnet-based VLAN has taken effect on the port:

•

Active

—The IP subnet-based VLAN has taken effect.

•

Inactive

—The IP subnet-based VLAN has not taken effect. For example, this

field displays

Inactive

in one of the following conditions:

{

The configuration of the IP subnet-based VLAN is not complete.

{

The port does not allow the IP subnet-based VLAN.

Related commands

•

display

ip-subnet-vlan

vlan

•

ip-subnet-vlan

•

port hybrid ip-subnet-vlan

display ip-subnet-vlan vlan

Use

display ip-subnet-vlan vlan

to display information about IP subnet-based VLANs.

Syntax

display ip-subnet-vlan vlan

{

vlan

id1

[

to vlan

id2

]

all

}

Views

Any view

Predefined user roles

network-admin

network-operator

Parameters

vlan

id1

: Specifies an IP subnet-based VLAN by its VLAN ID in the range of 1 to 4094.

vlan

id1 to vlan

id2

: Specifies a VLAN ID range. Both the

vlan-id1

and the

vlan-id2

arguments are in

the range of 1 to 4094. The value for the

vlan-id2

argument must be equal to or greater than the

value for the

vlan-id1

argument.

Содержание FlexNetwork 5130 HI series



















































































































































































































































































































Результаты поиска

Содержание FlexNetwork 5130 HI series

Отзывы:

Похожие инструкции для FlexNetwork 5130 HI series

Бренды по названию

Популярные бренды

HP FlexNetwork 5130 HI series, Справочник по командам

Результаты поиска

Содержание FlexNetwork 5130 HI series

Отзывы:

Похожие инструкции для FlexNetwork 5130 HI series

Бренды по названию

Популярные бренды