manualshive.com logo in svg

HP FlexNetwork 5130 HI series, Справочник по командам

Поделиться
Скачать
HP FlexNetwork 5130 HI series Скачать руководство пользователя страница 183

 

175 

Before you configure parameters for a VLAN interface, use this command to shut it down to prevent 
the configuration from affecting the network. After you complete the VLAN interface configuration, 
use the 

undo shutdown 

command to make the settings take effect. 

To troubleshoot a failed interface, you can use the 

shutdown 

command and then the 

undo 

shutdown

 command on the interface to see whether it recovers. 

In a VLAN, the state of any Ethernet port is independent of the state of the VLAN interface.  

Examples 

# Shut down VLAN-interface 2, and then bring it up. 

<Sysname> system-view 

[Sysname] interface vlan-interface 2 

[Sysname-Vlan-interface2] shutdown 

[Sysname-Vlan-interface2] undo shutdown 

vlan 

Use 

vlan vlan-id 

to create a VLAN and enter its view or to enter the view of an existing VLAN.  

Use 

vlan

 

vlan-id1 to vlan-id2 

to create VLANs 

vlan-id1

 through 

vlan-id2

, except reserved VLANs. 

Use 

vlan all 

to create VLANs 1 through 4094. 

Use 

undo vlan 

to delete the specified VLANs. 

Syntax 

vlan

 { 

vlan-id1 

[

 to vlan-id2 

]

 

|

 all

 } 

undo vlan 

{ 

vlan-id1 

[

 to vlan-id2 

]

 

|

 all

 } 

Default 

VLAN 1 (system default VLAN) exists.  

Views 

System view 

Predefined user roles 

network-admin 

Parameters 

vlan-id1

, 

vlan-id2

: Specifies a VLAN ID. The value range is 1 to 4094. 

vlan-id1

 

to

 

vlan-id2

: Specifies a VLAN range. The 

vlan-id1

 and 

vlan-id2

 arguments specify VLAN IDs. 

The value range for each of the two arguments is 1 to 4094. The value for the 

vlan-id2

 argument 

must be equal to or greater than the value for the 

vlan-id1 

argument. 

all

: Creates or deletes all VLANs except reserved VLANs.  

Usage guidelines 

You cannot create or delete the system default VLAN (VLAN 1). 

You cannot create or delete reserved VLANs. 

Before you delete a dynamic VLAN, a VLAN with a QoS policy applied, or a VLAN locked by an 
application, you must first remove the configuration from the VLAN. 

Examples 

# Create VLAN 2 and enter its view.  

<Sysname> system-view 

[Sysname] vlan 2 

Содержание FlexNetwork 5130 HI series



















































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды