manualshive.com logo in svg

HP FlexNetwork 5130 HI series, Справочник по командам

Поделиться
Скачать
HP FlexNetwork 5130 HI series Скачать руководство пользователя страница 180

 

172 

You cannot create a VLAN interface for a sub-VLAN. For more information about sub-VLANs, see 

Layer 2—LAN Switching Configuration Guide.

 

You cannot create VLAN interfaces for secondary VLANs that meet the following requirements:  

•

 

Associated with the same primary VLAN.  

•

 

Enabled with Layer 3 communication in VLAN interface view of the primary VLAN interface.  

For more information about secondary VLANs, 

Layer 2—LAN Switching Configuration Guide.

 

Examples 

# Create VLAN-interface 2, and enter its view. 

<Sysname> system-view 

[Sysname] vlan 2 

[Sysname-vlan2] quit 

[Sysname] interface vlan-interface 2 

[Sysname-Vlan-interface2] 

Related commands 

display interface vlan-interface

 

mtu 

Use 

mtu 

to set the MTU for a VLAN interface. 

Use 

undo mtu 

to restore the default. 

Syntax 

mtu

 

size

 

undo mtu 

Default 

The MTU of a VLAN interface is 1500 bytes. 

Views 

VLAN interface view 

Predefined user roles 

network-admin 

Parameters 

size

: Sets the MTU in bytes, in the range of 128 to 1500.  

Usage guidelines 

The 

ip mtu

 or 

mtu

 command configuration on an interface takes effect on only the packets sent to 

the CPU for software forwarding, including the packets destined to or sourced from the interface. 
Configure the MTU as appropriate to avoid fragmentation.  

If you configure both the 

mtu

 and 

ip mtu

 commands on a VLAN interface, the MTU set by the 

ip mtu

 

command is used for fragmentation. For more information about the 

ip mtu

 command, see 

Layer 

3—IP Services Command Reference

. 

Examples 

# Set the MTU to 1492 bytes for VLAN-interface 1. 

<Sysname> system-view 

[Sysname] interface vlan-interface 1 

[Sysname-Vlan-interface1] mtu 1492 

Содержание FlexNetwork 5130 HI series



















































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды