manualshive.com logo in svg

HP E1328A, Руководство по обслуживанию, Страница: 33 / 70

Поделиться
Скачать
HP E1328A Скачать руководство пользователя страница 33

150       PRINT TABXY(1,10),"New current output on Channel";Chan;" =
";Amps(Chan,I)*1.E + 3;"mA "
160       INPUT " Enter MEASURED current value (in mA) ",Meas(Chan,I)
170      GOSUB Accuracy 
180 Accuracy: ! 
190       Acc(Chan,I) = .0035*ABS(Amps(Chan,I)) + 2.2665E-4 
200       Llim(Chan,I) = Amps(Chan,I) - Acc(Chan,I) 
210       Ulim(Chan,I) = Amps(Chan,I) + Acc(Chan,I) 
220       IF Meas(Chan,I)*1.E-3 < (Chan,I) OR Meas(Chan,I)*1.E-3 >
Ulim(Chan,I) THEN 
230         PRINT TABXY(1,9),"Test FAILED on Channel";Chan;"for
";Amps(Chan,I)*1.E + 3;"mA " 
240       ELSE 
250         PRINT TABXY(1,9),"Test PASSED on Channel";Chan;"for
";Amps(Chan,I)*1.E + 3;"mA " 
260       END IF 
270     NEXT I 
280   NEXT Chan 
290   PRINT TABXY(1,18),"Current Accuracy Tests Complete" 
300   END

Performance
Test Record

Table 4-2, Performance Test Record for the HP E1328A DAC, can be used
to record the results of each Operation Verification and Performance
Verification test for the HP E1328A DAC (this record can be copied if
desired). The record includes the DAC upper and lower limits, HP 3458A
measurement uncertainty, and the Test Accuracy Ratio (TAR) for the test.

The values for DAC accuracy, HP 3458A measurement uncertainty and
TAR in Table 4-2 assume the following conditions. If your test conditions
differ from these conditions, you will need to compute the appropriate
values.

•

Calibration ON state (CALx:STAT ON) for each channel

•

1 k

Ω

  load for voltage accuracy measurements

•

500 

Ω

  load for current accuracy measurements

•

Test temp ASSUMED to be 

±

 5° C different than cal temp

•

1-year specifications for DAC accuracy

•

1-year specifications for HP 3458A meas uncertainty

NOTE

For the conditions listed, all Test Accuracy Ratios (TARs) exceed 4:1

Chapter 4

Verification Tests  33

Содержание E1328A







































































Отзывы:

Нет отзывов