HP E1328A Скачать руководство пользователя страница 17 | Manualshive

Страница: 17 / 70

HP E1328A Скачать руководство пользователя страница 17

Chapter 3

Operating Instructions

Introduction

This chapter lists operating information for the HP E1328A D/A Converter,
including:

•

D/A Converter operation

•

Operator’s check (self-test)

D/A Converter
Operation

See the HP E1328A 4-Channel D/A Converter User’s Manual for D/A
Converter operation, including:

•

Getting started

•

Configuring the D/A Converter

•

Using the D/A Converter

•

Understanding the D/A Converter

•

D/A Converter command reference

•

D/A Converter specifications

•

D/A Converter error messages

Operator’s
Check

The Operator’s Check for the HP E1328A D/A Converter consists of
sending the self-test (*TST?) command and checking the return. The
operator’s check can be used at any time to verify the D/A Converter is
connected properly and is responding to the self-test command. See
Chapter 8 - Service for a list of D/A Converter self-test errors.

CAUTION

The *TST? command temporarily resets the D/A Converter (to
0 V or 0 A output) on each channel. Make sure any devices
connected to the DAC will not be adversely affected before
using *TST?.

As required, see the mainframe user’s manual for information on address
selection. See the HP E1328A User’s Manual for information on D/A
Converter SCPI commands.

Chapter 3

Operating Instructions 17

«
...
15
16
17
18
19
...
»

Содержание E1328A







































































Отзывы:

Нет отзывов