HP E1328A Скачать руководство пользователя страница 15 | Manualshive

Страница: 15 / 70

HP E1328A Скачать руководство пользователя страница 15

Chapter 2

Installation

Introduction

This chapter provides information to install the HP E1328A D/A Converter,
including initial inspection, preparation for use, environment, storage and
shipment.

Initial
Inspection

Inspect the shipping container for damage.  If the shipping container or
cushioning material is damaged, keep the container until the shipment
contents have been checked and the instrument has been checked
mechanically and electrically.  See Chapter 1 (Figure 1-1) for shipment
contents.  See Chapter 4 for procedures to check electrical performance.

WARNING

To avoid possible hazardous electrical shock, do not perform
electrical tests if there are signs of shipping damage to any
portion of the outer enclosure (covers, panels, etc.).

If the contents are incomplete, if there is mechanical damage or defect, or if
the instrument does not pass the electrical performance tests, notify your
nearest Hewlett-Packard Sales and Service Office. If the shipping container
is damaged or the cushioning material shows signs of stress, notify the
carrier as well as Hewlett-Packard, and keep the shipping materials for the
carrier’s inspection.

Preparation for
Use

See Chapter 2 of the HP E1328A User’s Manual to prepare the
HP E1328A D/A Converter for use. See the appropriate mainframe user’s
manual(s) to prepare your mainframe. If your mainframe is not
manufactured by Hewlett-Packard, consult the manufacturer for a list of
available manual(s).

Recommended operating environment for the HP E1328A D/A Converter is
0

o

C to +55

o

C with humidity <65% relative (0

o

C to +40

o

C). The instrument

should be stored in a clean, dry environment. For storage and shipment, the
temperature range is -40

o

C to +75

o

C with humidity <65% relative humidity

(0

o

C to +40

o

C).

Chapter 2

Installation 15

«
...
13
14
15
16
17
...
»

Содержание E1328A







































































Отзывы:

Нет отзывов