HP E1328A Скачать руководство пользователя страница 12 | Manualshive

Страница: 12 / 70

HP E1328A Скачать руководство пользователя страница 12

DAC
Description

The HP E1328A DAC is an "instrument" in the slots of a VXIbus
mainframe. As such, it is assigned an error queue, input and output buffers,
status registers, and is allocated a portion of mainframe memory for reading
storage.

NOTE

Instruments are based on the logical addresses of the plug-in modules. See
the HP 75000 Series B Installation and Getting Started Guide to set the
addresses to create an instrument.

There are two E1328A DAC functions (see Table 1-1):

•

Isolated Voltage DACs

•

Isolated Current DACs

Table 1-1. HP E1328A 4-Channel D/A Converter Functions

Function/
Feature

Chs

Description

Voltage
DAC

1,2,3,4

Output DC voltage up to

±

10.92 V independently on

each channel. Can use remote voltage sensing with
"no-fault" operation. Connect multiple channels in
series to increase the output to

±

48 Vdc for a single

module. All four channels are independently isolated
and may be floated up to 350 Vdc from ground. Each
channel can be calibrated electronically to 24-hour
specifications.

Current
DAC

1,2,3,4

Output DC current up to

±

21.8 mA independently on

each channel. Connect multiple channels in parallel
to increase the output to

±

96 mA for a single module.

All four channels are independently isolated and may
be floated up to 350 Vdc from ground. Each channel
can be calibrated electronically to 24-hour
specifications.

DAC Specifications

DAC specifications are listed in Appendix A of the HP E1328A Users
Manual. These specificaitions are the performance standards or limits
against which the instrument may be tested.

12 General Information

Chapter 1

«
...
10
11
12
13
14
...
»

Содержание E1328A







































































Отзывы:

Нет отзывов