HP Compaq dx7200 MT Скачать руководство пользователя страница 55

Страница: 55 / 216

Service Reference Guide, dx7200

390812-001

4–1

Serial and Parallel ATA Drive Guidelines and

Features

✎

Serial ATA = SATA

Parallel ATA = PATA

HP only supports the use of a MultiBay PATA (IDE) hard drive on this model of computer.
3.5-inch PATA hard drives are not supported.

4.1 SATA 1.5 and 3.0 Hard Drives

SATA connectors on the system board are color coded to make identification easier.

✎

If there is an error on the application of the attach rules, a POST error message may be displayed.

Serial ATA Hard Drive Characteristics

Number of pins/conductors in data cable

7/7

Number of pins in power cable

Maximum data cable length

39.37 in (100 cm)

Data interface voltage differential

400-700 mV

Drive voltages

3.3 V, 5V, 12 V

Jumpers for configuring drive

N/A

Data transfer rate, 40 GB

1.5 Gb/s

3.0 Gb/s (some models)

Data transfer rate, 80 GB and greater

3.0 Gb/s

SATA Identification

Color

Port

Attachment

Sequence

Primary channel, device 0

Dark blue

SATA 0

Primary channel, device 1

Light Blue

SATA 2

Secondary channel, device 0

White

SATA 1

Secondary channel, device 1

Orange

SATA 3

Содержание Compaq dx7200 MT

























































































































































































































Результаты поиска

Содержание Compaq dx7200 MT

Отзывы:

HP Compaq dx7200 MT, Справочное руководство, Страница: 55 / 216

Результаты поиска

Содержание Compaq dx7200 MT

Отзывы: