HP Compaq dx2100 MT Series Скачать руководство пользователя страница 57

Страница: 57 / 116

Service Reference Guide, dx2100 MT

404569-001

6–15

Removal and Replacement Procedures— Microtower (MT) Chassis

6.9 Front I/O Panel Housing Assembly

1. Prepare the computer for disassembly (

Section 6.1, “Preparation for Disassembly”

2. Remove the access panel and rotate the computer so the system board is parallel to the table

to make it easier to work on (

Section 6.1, “Preparation for Disassembly”

3. Disconnect two attaching cables from the system board: the power switch/LED cable, and

the front USB cable.

4. Remove the two screws

that secure the housing to the chassis and then pull the housing

away from the chassis.

To install the housing assembly, reverse the removal procedures.

Содержание Compaq dx2100 MT Series





















































































































Результаты поиска

Содержание Compaq dx2100 MT Series

Отзывы:

Похожие инструкции для Compaq dx2100 MT Series

Бренды по названию

Популярные бренды

HP Compaq dx2100 MT Series, Руководство по обслуживанию и справочник

Результаты поиска

Содержание Compaq dx2100 MT Series

Отзывы:

Похожие инструкции для Compaq dx2100 MT Series

Бренды по названию

Популярные бренды