HP Compaq dc5100 Series Скачать руководство пользователя страница 14

Страница: 14 / 230

2–4

376220-001

Service Reference Guide, dc5100

Setup Utilities and Diagnostics Features

2.2.2 Computer Setup Menu

Heading

Option

Description

File System

Information

Lists:

• Product name
• Processor type/speed/stepping
• Cache size (L1/L2)
• Installed memory size/speed, number of channels (single or

dual) (if applicable)

• Integrated MAC address for embedded, enabled NIC (if

applicable)

• System ROM (includes family name and version)
• Chassis serial number
• Asset tracking number

About

Displays copyright information.

Set Time and Date

Allows you to set system time and date.

Replicated Setup

Save to Removable Media

Saves system configuration, including CMOS, to a formatted
1.44-MB diskette, a USB flash media device, or a diskette-like
device (a storage device set to emulate a diskette drive).

Restore from Removable Media

Restores system configuration from a diskette, a USB flash media
device, or a diskette-like device.

Default Setup

Save Current Settings as Default

Saves the current system configuration settings as the default.

Restore Factory Settings as Default

Restores the factory system configuration settings as the default.

Apply Defaults
and Exit

Applies the currently selected default settings and clears any
established passwords.

Ignore Changes
and Exit

Exits Computer Setup without applying or saving any changes.

Save Changes and
Exit

Saves changes to system configuration or default settings and exits
Computer Setup.

✎

Support for specific Computer Setup options may vary depending on the hardware configuration.

Содержание Compaq dc5100 Series







































































































































































































































Результаты поиска

Содержание Compaq dc5100 Series

Отзывы:

Похожие инструкции для Compaq dc5100 Series

Бренды по названию

Популярные бренды

HP Compaq dc5100 Series, Руководство по обслуживанию и справочник

Результаты поиска

Содержание Compaq dc5100 Series

Отзывы:

Похожие инструкции для Compaq dc5100 Series

Бренды по названию

Популярные бренды