HP BladeSystem c3000 Скачать руководство пользователя страница 62 | Manualshive

Страница: 62 / 108

background image

Enclosure troubleshooting 62

Symptoms: Insight Display reports blue device errors

Symptom

Additional information

Required steps

The Insight Display Health Summary
screen reports a device bay with a

"blue" color.
After rebooting the Onboard
Administrator, it can take up to 5

minutes for all start-up processes to
complete. During this time, various
devices and fans may display a blue

status.

A long-lasting "blue" device color
indicates that the Onboard
Administrator does not

communicate properly with the
device in the specific enclosure bay.
Several possible causes exist for this

condition:

•

The Onboard Administrator or

OA tray may not be installed

properly in the enclosure.

•

The device has not completed

the start-up process, which can
take several minutes per device.

•

The iLO on the server blade

does not have an IP address.

•

When the Virtual Connect

modules are being used, the
server blade does not have a

VC profile.

•

The Onboard Administrator

power-on delay function has not
had time to complete the

power-on sequence.

Begin with step 1.

The Insight Display Health Summary
screen shows a fan bay with a blue

color.

Fans may not be located properly in
the appropriate bays.

Follow the instructions on the Insight
Display for proper fan locations.
Install fans in the correct bay

locations.

Procedures: Insight Display reports blue device errors

CAUTION:

Some troubleshooting procedures require powering down an entire enclosure. To

avoid possible data loss, always secure permission before powering down an enclosure.

CAUTION:

If you are using a Virtual Connect environment, some of these procedures might

cause the loss of Virtual Connect credentials and the loss of communication between the Onboard

Administrator and the Virtual Connect Interconnect module. Ensure the Virtual Connect
configuration is backed up before proceeding with any of the following procedures. Virtual

Connect configuration can be backed up by using Virtual Connect GUI or Virtual Connect
Support Utility.

CAUTION:

To avoid data loss, do not remove an Onboard Administrator when the Insight

Display shows a firmware update in progress. During this activity, the Insight Display displays the
Firmware Update screen with the Lock icon and the firmware update progress bar.

«
...
60
61
62
63
64
...
»

Содержание BladeSystem c3000













































































































Отзывы:

Нет отзывов

Похожие инструкции для BladeSystem c3000

Бренд: H&S Страницы: 32

Sun Fire B1600 Administration

Бренд: Sun Microsystems Страницы: 402

Бренд: National Instruments Страницы: 65

Бренд: National Instruments Страницы: 52

Бренд: iXsystems Страницы: 12

Total Access 850

Бренд: ADTRAN Страницы: 292

Бренд: Philips Страницы: 87

Бренд: VXI Страницы: 35

Raven MIL-RCM16A

Бренд: MiLAN Страницы: 53

Бренд: EtherWAN Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды