HP BladeSystem c3000 Скачать руководство пользователя | Manualshive

Страница: 41 / 108

background image

Enclosure troubleshooting 41

Step

Server blade errors action and verification

Verification

Wait for up to 2 minutes, then check the Insight Display.
If the Insight Display illuminates and the Insight Display buttons operate properly, then
install OA #

Y

, if present, in OA bay

Y

to complete the repair.

If the issue still exists, continue to the next step.

Step 18

Action

Replace the OA tray:

1

Remove OA #

X

.

2

Remove the OA tray.

3

Install a service spare OA tray.

4

Install OA #

X

in bay

X

.

Verification

Wait for up to 2 minutes, and then check the Insight Display.
If the Insight Display illuminates and the Insight Display buttons operate properly, then
install OA #

Y

, if present, in bay Y to complete the repair.

If the issue still exists, then the OA tray did not fail. Continue to the next step.

Step 19

Action

Contact an authorized service provider to complete the midplane assembly replacement

(on page

Partner blade troubleshooting

Partner blades are installed in a device bay. The partner blades are either connected to a server blade or
interconnect module in the same enclosure. Partner blades cannot be powered down individually. This
section describes the unique troubleshooting characteristics of those partner blades.
For more information, see the component documentation.

Symptoms: Partner blade errors

Error indication

Initial step

Required steps

Insight Display reports error on

suspect partner blade

—

To correct the issue, follow the
Insight Display steps.

Partner blade health LED is off —

Begin with step 1

Partner blade health LED is

amber

For proper installation and support, most

partner blades require a partner server
blade to be installed and powered off
during partner blade installation. If the

partner blade is installed while the
partner server blade is powered up, then
power down the partner server blade

before powering up the partner blade.
Partner blades for interconnect modules
require the interconnect module to be

installed for operation.

To correct the issue, follow the

Insight Display steps.

Partner blade health LED is
green, but another LED on this

partner blade is red

—

For LED information, see the partner
blade documentation.

«
...
39
40
41
42
43
...
»

Содержание BladeSystem c3000













































































































Отзывы:

Нет отзывов

Похожие инструкции для BladeSystem c3000

NG4access ODF Platform Value-Added Module

Бренд: CommScope Страницы: 30

Бренд: Siemens Страницы: 1976

Бренд: Panasonic Страницы: 47

Бренд: nMedia Страницы: 4

Бренд: nMedia Страницы: 4

Бренд: nMedia Страницы: 7

Бренд: nMedia Страницы: 8

Бренд: nMedia Страницы: 9

Бренд: Cross Technologies Страницы: 5

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды