manualshive.com logo in svg

HP Aruba 6400 Series, Руководство по установке и началу работы

Поделиться
Скачать
HP Aruba 6400 Series Скачать руководство пользователя страница 87

3

3

1

2

2

d. Firmly close the extractor handles.
e. Tighten the screws at the top and bottom of the module.

Replacing a fan tray

Fan trays are installed in the slots on the rear of the chassis.

CAUTION: Replace only one fan tray at a time. Removing more than one fan tray at a time

compromises system cooling, risks damage to the hardware, and can cause the switch to shut

down abruptly.

CAUTION: For proper cooling and ventilation, a powered-up 6400 Series chassis must have all

fan trays installed and all four fans in each fan tray running.
• Do not remove a fan tray from a powered up switch without having a replacement fan tray

available.

• When replacing a fan tray in an operating switch, install the replacement fan tray within two

minutes of removing the original fan tray.

• Ensure that all fans in the replacement fan tray are operating after installation.
• If replacing more than one fan tray, ensure each fan tray is correctly installed and operational

before removing the next fan tray.

Chapter 9 Adding or replacing switch components

87

Содержание Aruba 6400 Series








































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды