HP Aruba 6400 Series Скачать руководство пользователя страница 75

Страница: 75 / 103

Procedure

1. Select an empty fan tray slot.
2. Insert a fan tray in the fan tray slot. The fan tray latch will sound an audible "click" when properly seated.
3. Tighten the two screws securing the fan tray in the slot.

4. To install another fan tray in another empty slot, repeat steps 1 through 3.

Installing the cable manager

The cable manager attaches to the rack ears. In the four-post mounting, the cable manager attaches to the

rack ear and the four-post mounting spacer.

Prerequisites
The switch is mounted in a four-post rack or with the rack ears in the front mounting position in a two post

rack mount. (See the illustrations under Two-post rack mounting.)

Procedure

1. Attach five cable retainers to each cable manager bulkhead, as shown.

Chapter 7 Installing components

Содержание Aruba 6400 Series








































































































Результаты поиска

Содержание Aruba 6400 Series

Отзывы:

Бренды по названию

Популярные бренды

HP Aruba 6400 Series, Руководство по установке и началу работы

Результаты поиска

Содержание Aruba 6400 Series

Отзывы:

Бренды по названию

Популярные бренды