HP Aruba 6400 Series Скачать руководство пользователя страница 71

Страница: 71 / 103

9. Power-on and verify that the installed power supply units are running properly. A steady green LED on

the front panel of a PSU indicates proper operation. (For more information on LED behavior, see the

latest version of the Monitoring Guide at https://asp.arubanetworks.com/downloads.)

NOTE: The 6400 Series chassis and PSUs do not include a power on/off switch. PSUs are

powered on by connecting the AC power cord at the rear of the chassis, and to an AC power

source.

Install management modules in slots 1 and 2

Skip this task if your management modules are already installed.

Aruba 6405 and 6410 : 1 and 2

Management module slots

Aruba 6405: 3 through 7

Aruba 6410: 3 through 12

Line module slots

Chapter 7 Installing components

Содержание Aruba 6400 Series








































































































Результаты поиска

Содержание Aruba 6400 Series

Отзывы:

Бренды по названию

Популярные бренды

HP Aruba 6400 Series, Руководство по установке и началу работы

Результаты поиска

Содержание Aruba 6400 Series

Отзывы:

Бренды по названию

Популярные бренды