HP Aruba 6400 Series Скачать руководство пользователя страница 49 | Manualshive

Страница: 49 / 103

background image

WARNING: If you are manually mounting the switch instead of using a mechanical lift, then

before proceeding in this chapter, reduce chassis weight by removing any installed switch

components, as described under Removing installed components from the chassis

NOTE: Unless otherwise noted, instructions in this chapter apply to both the Aruba 6405 Switch

and the Aruba 6410 Switch.

(Optional) Installing the chassis in a non-rack mounted

position

Skip this procedure if you plan to mount the switch in an equipment rack. (See Mounting the chassis in a

rack.)
The following conditions must be met when performing a rack-free installation:

• A fully-populated Aruba 6405 Switch can weigh up to 61 kg (133 lbs) and a fully populated Aruba 6410

Switch can weigh up to 100 kg (219 lbs). The structure and floor supporting the switch must be able to

withstand this weight.

• The switch should be supported by a sturdy, flat surface.

NOTE: The chassis is not equipped with rubber feet. Take care to avoid marking or scratching

the mounting surface.

WARNING: To reduce the risk of personal injury or damage to equipment in a rack-free

environment:
• Never stack the Aruba 6400 chassis on top of another chassis or other equipment.
• Never place equipment on top of the Aruba 6400 chassis.
• Never place an Aruba 6400 chassis on a surface that cannot support the weight of the fully

populated chassis. (up to 61 kg (133 lbs) for a 6405 model and up to 100 kg (219 lbs) for a

6410 model.)

Manually positioning the chassis on a non-rack mount surface

Skip this step if you plan to use a mechanical lift to move the chassis.

Procedure

1. Ensure that site preparation for the mounting site has been completed. See Site preparation.
2. Move the switch to the mounting site as described under Move the chassis to the mounting location.
3. Position the switch with the rear of the chassis resting on the mounting surface.

Chapter 6

Mounting the switch

Chapter 6 Mounting the switch

49

«
...
47
48
49
50
51
...
»

Содержание Aruba 6400 Series








































































































Отзывы:

Нет отзывов

Похожие инструкции для Aruba 6400 Series

Бренд: GarrettCom Страницы: 24

Бренд: Maipu Страницы: 21

Бренд: Maico Страницы: 56

Бренд: OEZ Страницы: 5

Бренд: wavin Страницы: 4

Бренд: AdLuminis Страницы: 8

Бренд: GarrettCom Страницы: 39

Бренд: A-Neuvideo Страницы: 26

Бренд: Magnum Страницы: 3

Cyber SWITCH 1000

Бренд: Cabletron Systems Страницы: 106

Бренд: DirectConnect Страницы: 10

Бренд: Phonocar Страницы: 2

Бренд: Lindy Страницы: 5

Бренд: Radware Страницы: 4

Бренд: LEGRAND Страницы: 4

Бренд: Accton Technology Страницы: 8

Бренд: Gefen Страницы: 12

Бренд: CoolGear Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды