HP A7500 Series Скачать руководство пользователя страница 134

Страница: 134 / 222

127

Field Description

Version Patch

version.

Temporary

Number of temporary patches

Common

Number of common patches

Current

Total number of patches

Running

Number of patches in the RUNNING state

Active

Number of patches in the ACTIVE state

Start-Address

Starting address of the memory patch area in the memory

patch active

Syntax

In standalone mode:

patch active

[

patch-number

]

slot

slot-number

In IRF mode:

patch active

[

patch-number

]

chassis

chassis-number

slot

slot-number

View

System view

Default level

3: Manage level

Parameters

patch-number

: Sequence number of a patch, with values depending on the patch file used.

slot

slot-number

: Specifies a card by its slot number. (in standalone mode)

chassis

chassis-number

slot

slot-number

: Specifies a card on an IRF member switch. The

chassis-number

argument refers to the ID of the IRF member switch, and the

slot-number

argument refers to the number of

the slot where the card resides. (in IRF mode)

Description

Use the

patch active

command to activate patches. The system will temporarily run the loaded patches.

•

If you execute the command with specifying the sequence number of a patch, all the DEACTIVE
patches (including the specified patch) before the specified patch will be activated.

•

If you execute the command without specifying the sequence number of a patch, all the DEACTIVE
patches will be activated.

NOTE:

•

The command is applicable to only patches in the DEACTIVE state.

•

After a system reboot, the original ACTIVE patches change to DEACTIVE and become invalid. To make
them effective, activate them again.

Содержание A7500 Series































































































































































































































Результаты поиска

Содержание A7500 Series

Отзывы:

Бренды по названию

Популярные бренды

HP A7500 Series, Справочник по командам

Результаты поиска

Содержание A7500 Series

Отзывы:

Бренды по названию

Популярные бренды