HP 8920A Скачать руководство пользователя страница 168 | Manualshive

Страница: 168 / 658

background image

168

S:\HP892XX\USRGUIDE\manual\callscrn.fb

Chapter 6, Call Processing Subsystem

CALL DATA Screen

Handoff

This field is used to initiate a handoff from the current voice channel assignments
to a new set of voice channel assignments. The voice channel number to hand the
mobile station off to, the channel location (NAMPS system type only), the initial
power level to use on the new voice channel, the DSAT sequence (NAMPS
system type only) to transpond on the mobile station, and the SAT tone frequency
to transpond on the new voice channel are specified using the

Chan:

,

Ch Loc:

,

Pwr Lvl:

,

DSAT:

, and

SAT:

fields in the

Voice Channel Assignment

section of the CALL CONTROL screen.

This field is used to initiate a handoff from the current voice channel assignments
to a new set of voice channel assignments. The voice channel number to hand the
mobile station off to, the initial power level to use on the new voice channel, and
the SAT tone frequency to transpond on the new voice channel are specified using
the

Chan:

,

Pwr Lvl:

, and

SAT:

fields in the

Voice Channel Assignment

section of the CALL CONTROL screen.

Order

This field is used to send an order on the forward voice channel to the mobile
station. The orders available are:

•

Change Power to Power Level 0 - 7

•

MRI (issues a request for mobile reported interference report, NAMPS system type
only)

Maintenance (puts the mobile station in maintenance mode)

•

Alert (alerts the mobile station)

The

Order

field is a one-of-many selection field. To send an order to the mobile

station select the

Order

field. A list of choices is displayed. Select the desired

order from the

Choices:

menu. Once the selection is made, a mobile station

control message is sent to the mobile station. The

Access

annunciator will light

momentarily while the Test Set is sending the mobile station control message.

A mobile station must be actively connected on a voice channel to the Test Set
(that is, the

Connect

annunciator must be lit) before you can attempt to send an

order to a mobile station.

When the

Authent

is set to

ON

, the

Order

field is not displayed.

«
...
166
167
168
169
170
...
»

Содержание 8920A



















































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 8920A

D-IMager EKL3104

Бренд: Panasonic Страницы: 13

Бренд: Labokey Страницы: 5

Бренд: E-Z Trail Страницы: 8

Бренд: B&K Страницы: 10

SafetuNet Alert

Бренд: Masimo Страницы: 2

Бренд: Tascam Страницы: 8

Бренд: B-K lighting Страницы: 5

Бренд: B-K lighting Страницы: 4

Бренд: B-K lighting Страницы: 3

SC 2 Deluxe EasyFix

Бренд: Kärcher Страницы: 12

Бренд: Kärcher Страницы: 16

Бренд: Xtool Страницы: 8

Бренд: SCHUNK Страницы: 2

Бренд: Garmin Страницы: 41

Бренд: impact Страницы: 8

Бренд: TOTAL10 Страницы: 16

Бренд: Furuno Страницы: 2

Labmatic 400.COM

Бренд: LABTEC Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды