HP 8920A Скачать руководство пользователя страница 135 | Manualshive

Страница: 135 / 658

background image

135

Chapter 6, Call Processing Subsystem

The CALL CONTROL Screen

[] Page

When lit, the

Page

annunciator indicates that the mobile station connected to the

Test Set is currently being paged on the forward control channel.

Phone Num:

This field displays the decoded MIN number received from the mobile station on
the reverse control channel in response to a forward control channel message. The

Phone Num:

field is displayed only when the

Display

field is set to

Data

and a

reverse control channel message containing this information has been decoded.

CAUTION:

Do not confuse the

Phone Num:

field, which is displayed in the upper right-hand portion of

the

CALL CONTROL

screen, with the

Phone Num

selection of the

MS Id

field.

NOTE:

An all zero MIN number (000000000), which does not represent a valid phone number, will
convert to the following phone number: 111111?111.

Register

This field is used to initiate a registration of the mobile station that is connected to
the Test Set. The Test Set must be in the active state (that is, the

Active

annunciator must be lit) before you can attempt to register the mobile station.

[] Register

When lit, the

Register

annunciator indicates that the mobile station connected

to the Test Set is being commanded to register with the Test Set.

Release

This field is used to terminate an active voice channel connection with the mobile
station. When the

Release

field is selected, a mobile station control message

with a release order is sent to the mobile station on the forward voice channel. A
mobile station must be actively connected on a voice channel to the Test Set (that
is, the

Connect

annunciator must be lit) before you can attempt to send a release

order to the mobile station.

«
...
133
134
135
136
137
...
»

Содержание 8920A



















































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 8920A

Бренд: York Fitness Страницы: 34

Бренд: OMCA Страницы: 36

Бренд: Salford Страницы: 64

Movie FL Black E27 Flaps

Бренд: Qazqa Страницы: 2

Бренд: Federal Signal Corporation Страницы: 4

Бренд: ParaBody Страницы: 7

Бренд: Haaga Страницы: 31

Бренд: SAMCHULLY Страницы: 48

Бренд: HAGS Страницы: 5

Бренд: HAGER WERKEN Страницы: 2

Бренд: TDR Страницы: 8

Бренд: UNIS Страницы: 16

Bathomatic Basic

Бренд: Unique Automation Страницы: 10

Бренд: Additel Страницы: 139

Бренд: 4iQ Страницы: 6

PowerGen 5650 Series

Бренд: Qnergy Страницы: 10

Бренд: Makita Страницы: 208

CIRCOLINA G10q T9

Бренд: Life Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды