HP 85106D Скачать руководство пользователя страница 147 | Manualshive

Страница: 147 / 244

HP 85106D Скачать руководство пользователя страница 147

5-34

HP 85106D mm-Wave System

HP 85104A Test Set Module

Disassembly Procedure

15. Disconnect the isolator mixer assembly arms by removing the screws

from the flange at the coupler interface.

16. Remove the mixer clamp.

17. Remove the two torx-head screws (size T-8) from the LO power divider

and remove the power divider.

18. Disconnect the main line isolator arm at the source interface by

removing the 4 hex-head screws from the flange.

19. Remove the hex-head screws from the coupler bracket.

20. Slide the coupler/isolator assembly to the rear of the instrument and

remove it.

21. For V-or W-band modules, remove A14 coupler/detector from A8 dual

directional coupler.

NOTE

The coupler/detector (A14) and the source block (A13) must be returned to
the factory together (attached with two screws) if either component is faulty.

22. Remove the torx-head screws from the coupler bracket and remove the

bracket.

23. Remove the 90° coaxial bend from the RF cable near the RF clamp on

the source block.

24. Turn the source block over and remove the four torx-head screws from

the top housing.

25. Remove the source module assembly which includes the aluminum bar

mount to complete the disassembly procedure for the HP 85104A test
set module. Refer to the assembly procedure that follows to reassemble
the test set module.

«
...
145
146
147
148
149
...
»

Содержание 85106D





















































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды