manualshive.com logo in svg

HP 5800, Справочник по командам

Поделиться
Скачать
HP 5800 Скачать руководство пользователя страница 56

 

47 

Default level 

2: System level 

Parameters 

number

: Specifies the maximum number of routes supported. The value ranges from 1 to 8192. 

warn-threshold

: Specifies a threshold for warning, ranging from 1 to 100, in percentages. When the 

percentage  of  the  number  of  existing  routes  to  the  maximum  number  of  routes  supported  exceeds  the 

specified threshold, the system gives an alarm message, but still allows new routes. If the number of routes 
in the VPN instance reaches the maximum supported, no more routes are added. 

simply-alert

: Specifies that when the number of routes exceeds the maximum number of routes supported, 

the system still accepts routes but generates a Syslog message. 

Examples 

# Configure VPN instance 

vpn1

 to support up to 1000 routes, and receive new routes after the number of 

existing routes exceeds the limit. 

<Sysname> system-view 

[Sysname] ip vpn-instance vpn1 

[Sysname-vpn-instance-vpn1] route-distinguisher 100:1 

[Sysname-vpn-instance-vpn1] routing-table limit 1000 simply-alert 

# Specify that the IPv6 VPN of VPN instance 

vpn3

 supports up to 1000 routes, and can receive new 

routes after the number of existing routes exceeds the limit. 

<Sysname> system-view 

[Sysname] ip vpn-instance vpn3 

[Sysname-vpn-instance-vpn3] route-distinguisher 100:3 

[Sysname-vpn-instance-vpn3] ipv6-family 

[Sysname-vpn-ipv4-vpn3] routing-table limit 1000 simply-alert 

vpn-target (VPN instance view/IPv6 VPN view) 

Description 

Use the 

vpn-target

 command to configure VPN targets for a VPN instance, an IPv4 VPN, or an IPv6 VPN. 

Use the 

undo vpn-target

 command to remove the specified or all VPN targets of a VPN instance, an IPv4 

VPN, or an IPv6 VPN. 
By default, no VPN targets are configured, and you must configure VPN targets when creating a VPN 

instance, an IPv4 VPN, or an IPv6 VPN. 

•

 

VPN targets configured in IPv6 VPN view is applicable to only the IPv6 VPN. 

•

 

VPN targets configured in IPv6 VPN view takes precedence over that configured in VPN instance 
view. If you configure VPN targets in both IPv6 VPN view and VPN instance view, those configured 

in IPv6 VPN view are applied to the IPv6 VPN. 

Syntax 

vpn-target

 vpn-target

&<1-8> [ 

both

 | 

export-extcommunity

 | 

import-extcommunity

 ] 

undo vpn-target

 

{ 

all

 | 

vpn-target

&<1-8> [ 

both

 | 

export-extcommunity

 | 

import-extcommunity

 ] } 

View 

VPN instance view, IPv6 VPN view 

Содержание 5800













































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды