manualshive.com logo in svg

HP 5800, Справочник по командам

Поделиться
Скачать
HP 5800 Скачать руководство пользователя страница 384

 

375 

Parameters  

vpn-instance-name

: Resets IPv6 BGP connections with the peers in a VPN instance. The VPN instance 

name is a case-sensitive string of 1 to 31 characters.

 

as-number

: Resets IPv6 BGP connections with the peers in an AS. The AS number is ranging from 1 to 

4,294,967,295. 

 

ipv6-address

: Resets the connection with the BGP peer identified by this IPv6 address. 

all

: Resets all IPv6 BGP connections in the specified VPN instance. 

external

: Resets EBGP sessions. 

Examples 

# Reset all IPv6 BGP connections in VPN instance 

vpn1

. 

<Sysname> reset bgp ipv6 vpn-instance vpn1 all 

reset bgp vpnv6 

Description 

Use the 

reset bgp vpnv6

 command to reset BGP VPNv6 connections. 

Syntax 

reset bgp vpnv6

 { 

as-number

 | 

ip-address

 | 

all

 | 

external

 | 

internal

 } 

View 

User view 

Default level 

1: Monitor level 

Parameters 

as-number

: Resets BGP VPNv6 connections with the peers in the AS identified by this number. 

as-number 

ranges from 1 to 4,294,967,295.

 

ip-address

: Resets the BGP VPNv6 connection with the BGP peer identified by this IP address. 

all

: Resets all BGP VPNv6 connections. 

external

: Resets EBGP VPNv6 connections. 

internal

: Resets IBGP VPNv6 connections. 

Examples 

# Reset all BGP VPNv6 connections to make new configurations take effect. 

<Sysname> reset bgp vpnv6 all

 

routing-table limit 

Description 

Use the 

routing-table

 

limit

 command to limit the maximum number of routes in a VPN instance, an IPv4 

VPN, or an IPv6 VPN, preventing too many routes from being accepted by a PE. 
Use the 

undo routing-table limit 

command to restore the default. 

The default maximum number of routes supported varies by device. 

Содержание 5800













































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды