HP 5800 Скачать руководство пользователя страница 253

Страница: 253 / 396

244

regular-expression

: Specifies a regular expression, which is a case-sensitive string of 1 to 256 characters.

Examples

# Display information about interfaces of any encapsulation types.

<Sysname> display l2vpn ccc-interface vc-type all

Total ccc-interface of CCC VC: 3

up (3), down (0)

Interface Encap Type State VC Type

Vlan2 ethernet up CCC

Vlan3 ethernet up bgp-vc

Vlan4 ethernet up static-vc

# Display information about interfaces of Kompella L2VPN VCs.

<Sysname> display l2vpn ccc-interface vc-type bgp-vc

Total ccc-interface of BGP VC: 1

up (1), down (0)

Interface Encap Type State VC Type

Vlan3 ethernet up bgp-vc

# Display information about interfaces of SVC L2VPN VCs that are in the state of UP.

<Sysname> display l2vpn ccc-interface vc-type svc-vc up

Total ccc-interface of SVC VC: 1,

up (1), down (0)

Interface Encap Type State VC Type

Vlan4 VLAN up static-vc

Table 96

Command output

Field Description

Total ccc-interface of XXX VC

Total interface number of L2VPN VCs of type xxx

Interface

Name of the interface

Encap Type

Encapsulation type of the interface

State

Status of the interface

VC Type

Encapsulation type of the L2VPN VC interface

display mpls l2vc

Description

Use the

display mpls l2vc

command to display information about Martini VCs configured on the router.

If you specify an interface, the command displays information about Martini VCs configured on the CE

interface.

Syntax

display mpls l2vc

[

interface

interface-type interface-number

[

service-instance

instance-id

] |

remote-info

]

[

{

begin

exclude

include

}

regular-expression

]

View

Any view

Содержание 5800













































































































































































































































































































































































































Результаты поиска

Содержание 5800

Отзывы:

Бренды по названию

Популярные бренды

HP 5800, Справочник по командам

Результаты поиска

Содержание 5800

Отзывы:

Бренды по названию

Популярные бренды