manualshive.com logo in svg

HP 5800, Справочник по командам

Поделиться
Скачать
HP 5800 Скачать руководство пользователя страница 206

 

197 

Examples 

# Configure a static CR-LSP on the transit node, setting its name to tunnel34, incoming interface to VLAN-
interface 3, incoming label to 123, outgoing interface to VLAN-interface 4, outgoing label to 253.  

<Sysname> system-view 

[Sysname] static-cr-lsp transit tunnel34 incoming-interface Vlan-interface 3 in-label 123 

outgoing-interface Vlan-interface 4 out-label 253 

tracert lsp te 

Description 

Use the 

tracert lsp te

 command to locate errors of MPLS TE tunnels.  

Syntax 

tracert lsp 

[ 

-a 

source-ip

 | 

-exp 

exp-value

 | 

-h 

ttl-value

 

| 

-r 

reply-mode

 |

-t 

time-out

 ]

 

* 

te 

interface-type 

interface-number

 

View 

Any view 

Default level 

0: Visit level 

Parameters 

-a

 source-ip

: Specifies the source IP address of the Echo Request messages.  

-exp

 exp-value

: Specifies the EXP value for the Echo Request messages. The 

exp-value

 parameter ranges 

from 0 to 7 and defaults to 0. 

-h

 ttl-value

: Specifies the TTL value for the Echo Request messages. The 

ttl-value

 parameter ranges from 1 

to 255 and defaults to 30. 

-r

 

reply-mode

:  Specifies  the  reply  mode  of  the  receiver  in  response  to  an  Echo  Request  message.  The 

reply-mode

 parameter can be 1 or 2, where 1 means “Do not respond” and 2 means “Respond using a 

UDP packet.” The default is 2. 

-t

 time-out

: Specifies the timeout interval for waiting for the response to an echo request message. The 

time-out

 parameter ranges from 0 to 65,535 and defaults to 2000, in milliseconds.  

te

 interface-type interface-number

: Specifies a tunnel interface. 

Examples 

# Tracert the MPLS TE tunnel of tunnel interface Tunnel 1.  

<Sysname> tracert lsp te tunnel 1 

LSP Trace Route FEC: TE TUNNEL IPV4 SESSION QUERY Tunnel1 , press CTRL_C to break. 

  TTL   Replier            Time    Type      Downstream 

  0                                Ingress   10.4.5.1/[1025] 

  1     10.4.5.1           1       Transit   100.3.4.1/[1024] 

  2     100.3.4.1          63      Transit   100.1.2.1/[3] 

  3     100.1.2.1          129     Egress 

Содержание 5800













































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды