manualshive.com logo in svg

HP 5800, Справочник по командам

Поделиться
Скачать
HP 5800 Скачать руководство пользователя страница 170

 

161 

Examples 

# Enable authentication on VLAN-interface 1. 

<Sysname> system-view 

[Sysname] interface vlan-interface 1 

[Sysname-Vlan-interface1] mpls rsvp-te authentication plain partner123 

mpls rsvp-te bfd enable 

Description 

Use the 

mpls rsvp-te bfd enable 

command on an RSVP-TE enabled interface to enable BFD for link 

detection.  
Use the 

undo mpls rsvp-te bfd enable 

command to disable BFD on an RSVP-TE enabled interface. 

By default, BFD for link detection is not enabled on an RSVP-TE enabled interface. 
Before enabling BFD for link detection on an interface, make sure that the interface is enabled with RSVP-
TE.  

Syntax 

mpls rsvp-te bfd enable 
undo mpls rsvp-te bfd enable 

View 

Interface view 

Default level 

2: System level 

Parameters 

None 

Examples 

# Enable BFD link detection on RSVP-TE enabled interface VLAN-interface 100. 

<Sysname> system-view 

[Sysname] interface vlan-interface 100 

[Sysname-Vlan-interface100] mpls rsvp-te bfd enable 

mpls rsvp-te blockade-multiplier 

Description 

Use the 

mpls rsvp-te blockade-multiplier

 command to configure the blockade multiplier. 

Use the 

undo mpls rsvp-te blockade-multiplier

 command to restore the default. 

The default blockade multiplier is 4. 
A ResvErr message establishes a blockade state in each node through which it passes to solve the killer 
reservation problem, where one request could deny service to another. The use of a blockade state allows 

a smaller request to be forwarded or established.  
The blockade timeout time is determined by the following equation: 
Blockade_Expired_Time = 

Kb

 × 

refresh-time

 

Содержание 5800













































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды