manualshive.com logo in svg

HP 5800, Справочник по командам

Поделиться
Скачать
HP 5800 Скачать руководство пользователя страница 136

 

127 

Field Description 

Authentication 

State of authentication: enabled or disabled. 

Reliability 

Whether the reliability feature is configured: yes or no. 

Retransmit interval 

Initial retransmission interval (in milliseconds). 

Increment value 

Increment value delta that governs the speed at which the interface 
increases the retransmission interval.  
Assume the initial interval is Rf seconds. If the interface does not 
receive an ACK message for a packet within this interval, it 

retransmits the packet after (1 + Increment value) × Rf seconds.

 

 

display mpls rsvp-te established 

Description 

Use the 

display

 

mpls rsvp-te

 

established

 command to display information about RSVP-TE tunnels. 

Syntax 

display mpls rsvp-te established

 [ 

interface

 

interface-type interface-number 

] [ 

|

 { 

begin

 | 

exclude

 | 

include

 } 

regular-expression

 ] 

View 

Any view 

Default level 

1: Monitor level 

Parameters 

interface

 interface-type interface-number

: Specifies an interface by its type and number. If you do not 

specify an interface, the command displays the RSVP-TE tunnel information of all interfaces. 

|

: Filters command output by specifying a regular expression. For more information about regular 

expressions, see the 

Fundamentals Configuration Guide

. 

begin

: Displays the first line that matches the specified regular expression and all lines that follow. 

exclude

: Displays all lines that do not match the specified regular expression. 

include

: Displays all lines that match the specified regular expression. 

regular-expression

: Specifies a regular expression, which is a case-sensitive string of 1 to 80 characters. 

Examples 

# Display RSVP-TE tunnel information for interface VLAN-interface 3. 

<Sysname> display mpls rsvp-te established interface vlan-interface 3 

Interface Vlan-interface3 

 Token Bucket Rate: 0.00            Peak Data Rate: 0.00 

 Tunnel Dest: 2.2.2.2               Ingress LSR ID: 3.3.3.3 

 Local LSP ID: 4                    Session Tunnel ID: 4 

 Next Hop Addr: 80.4.1.1 

 Upstream Label: 1024               Downstream Label: 3 

Содержание 5800













































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды